Understanding three-dimensional (3D) root traits is essential to improve water uptake, increase nitrogen capture, and raise carbon sequestration from the atmosphere. However, quantifying 3D root traits by reconstructing 3D root models for deeper field-grown roots remains a challenge due to the unknown tradeoff between 3D root-model quality and 3D root-trait accuracy. Therefore, we performed two computational experiments. We first compared the 3D model quality generated by five state-of-the-art open-source 3D model reconstruction pipelines on 12 contrasting genotypes of field-grown maize roots. These pipelines included COLMAP, COLMAP+PMVS (Patch-based Multi-View Stereo), VisualSFM, Meshroom, and OpenMVG+MVE (Multi-View Environment). The COLMAP pipeline achieved the best performance regarding 3D model quality versus computational time and image number needed. In the second test, we compared the accuracy of 3D root-trait measurement generated by the Digital Imaging of Root Traits 3D pipeline (DIRT/3D) using COLMAP-based 3D reconstruction with our current DIRT/3D pipeline that uses a VisualSFM-based 3D reconstruction on the same dataset of 12 genotypes, with 5–10 replicates per genotype. The results revealed that (1) the average number of images needed to build a denser 3D model was reduced from 3000 to 3600 (DIRT/3D [VisualSFM-based 3D reconstruction]) to around 360 for computational test 1, and around 600 for computational test 2 (DIRT/3D [COLMAP-based 3D reconstruction]); (2) denser 3D models helped improve the accuracy of the 3D root-trait measurement; (3) reducing the number of images can help resolve data storage problems. The updated DIRT/3D (COLMAP-based 3D reconstruction) pipeline enables quicker image collection without compromising the accuracy of 3D root-trait measurements.

Tree training systems for temperate fruit have been developed throughout history by pomologists to improve light interception, fruit yield, and fruit quality. These training systems direct crown and branch growth to specific configurations. Quantifying crown architecture could aid the selection of trees that require less pruning or that naturally excel in specific growing/training system conditions. Regarding peaches [Prunus persica (L.) Batsch], access tools such as branching indices have been developed to characterize tree-crown architecture. However, the required branching data (BD) to develop these indices are difficult to collect. Traditionally, BD have been collected manually, but this process is tedious, time-consuming, and prone to human error. These barriers can be circumnavigated by utilizing terrestrial laser scanning (TLS) to obtain a digital twin of the real tree. TLS generates three-dimensional (3D) point clouds of the tree crown, wherein every point contains 3D coordinates (x, y, z). To facilitate the use of these tools for peach, we selected 16 young peach trees scanned in 2021 and 2022. These 16 trees were then modeled and quantified using the open-source software TreeQSM. As a result, “in silico” branching and biometric data for the young peach trees were calculated to demonstrate the capabilities of TLS phenotyping of peach tree-crown architecture. The comparison and analysis of field measurements (in situ) and in silico BD, biometric data, and quantitative structural model branch uncertainty data were utilized to determine the reconstructive model's reliability as a source substitute for field measurements. Mean average deviation when comparing young tree (YT) height was approx. 5.93%, with crown volume was approx. 13.26% across both 2021 and 2022. All point clouds of the YTs in 2022 showed residuals lower than 12 mm to cylinders fitted to all branches, and mean surface coverage greater than 40% for both the trunk and primary branching orders.

Trichomes show 47 morphological phenotypes, while literature reports only two root hair phenotypes in all plants. However, could hair-like structures exist below-ground in a similar wide range of morphologies like trichomes? Genetic mutants and root hair stress phenotypes point to the possibility of uncharacterized morphological variation existing belowground. For example, such root hairs in Arabidopsis (Arabidopsis thaliana) can be wavy, curled, or branched. We found hints in the literature about hair-like structures that emerge before root hairs belowground. As such, these early emerging hair structures can be potential exceptions to the contrasting morphological variation between trichomes and root hairs. Here, we show a previously unreported ‘hooked’ hair structure growing below-ground in common bean. The unique ‘hooking’ shape distinguishes the ‘hooked hair’ morphologically from root hairs. Currently, we cannot fully characterize the phenotype of our observation due to the lack of automated methods for phenotyping root hairs. This phenotyping bottleneck also handicaps the discovery of more morphology types that might exist below-ground as manual screening across species is slower than computer-assisted high-throughput screening.

The development of crops with deeper roots holds substantial promise to mitigate the consequences of climate change. Deeper roots are an essential factor to improve water uptake as a way to enhance crop resilience to drought, to increase nitrogen capture, to reduce fertilizer inputs, and to increase carbon sequestration from the atmosphere to improve soil organic fertility. A major bottleneck to achieving these improvements is high-throughput phenotyping to quantify root phenotypes of field-grown roots. We address this bottleneck with Digital Imaging of Root Traits (DIRT)/3D, an image-based 3D root phenotyping platform, which measures 18 architecture traits from mature field-grown maize (Zea mays) root crowns.

The 2022 NAPPN Annual Conference is the largest meeting on plant phenotyping in North America and will be held in Athens, Georgia. The meeting will highlight the most recent interdisciplinary advances from biology, engineering, computer science, and mathematics in the rapidly developing field of Plant Phenotyping.